The following codes are the standard GSM codes for various network services. Most Nokia phones have easier ways to activate them through the menus. Check the guides for your model.

. Call Diverting

- All
To Activate: * * 21 * NUMBER # [SEND]
To Cancel: # # 21 # [SEND]
To Check: * # 21 # [SEND]

- No Answer
To Activate: * * 61 * NUMBER # [SEND]
To Cancel: # # 61 # [SEND]
To Check: * # 61 # [SEND]

- Unreachable
To Activate: * * 62 * NUMBER # [SEND]
To Cancel: # # 62 # [SEND]
To Check: * # 62 # [SEND]

- Busy
To Activate: * * 67 * NUMBER # [SEND]
To Cancel: # # 67 # [SEND]
To Check: * # 67 # [SEND]
To Cancel All Call Forwarding # # 002 # [SEND]

. Call Waiting

To Activate: * 43 # [SEND]
To Deactivate: # 43 # [SEND]
To Check: * # 43 # [SEND]

. Calling Line Identity
[Read More…]

CAM - A cam is a theater rip usually done with a digital video camera. A mini tripod is sometimes used, but a lot of the time this wont be possible, so the camera make shake. Also seating placement isn’t always idle, and it might be filmed from an angle. If cropped properly, this is hard to tell unless there’s text on the screen, but a lot of times these are left with triangular borders on the top and bottom of the screen. Sound is taken from the onboard microphone of the camera, and especially in comedies, laughter can often be heard during the film. Due to these factors picture and sound quality are usually quite poor, but sometimes we’re lucky, and the theater will be fairly empty and a fairly clear signal will be heard.

TELESYNC (TS) - A telesync is the same spec as a CAM except it uses an external audio source (most likely an audio jack in the chair for hard of hearing people). A direct audio source does not ensure a good quality audio source, as a lot of background noise can interfere. A lot of the times a telesync is filmed in an empty cinema or from the projection booth with a professional camera, giving a better picture quality. Quality ranges drastically, check the sample before downloading the full release. A high percentage of Telesyncs are CAMs that have been mislabeled.

TELECINE (TC) - A telecine machine copies the film digitally from the reels. Sound and picture should be very good, but due to the equipment involved and cost telecines are fairly uncommon. Generally the film will be in correct aspect ratio, although 4:3 telecines have existed. A great example is the JURASSIC PARK 3 TC done last year. TC should not be confused with TimeCode , which is a visible counter on screen throughout the film.

[Read More…]

When a computer is first turned on, or rebooted, its BIOS performs a power-on self test (POST) to test the system’s hardware, checking to make sure that all of the system’s hardware components are working properly. Under normal circumstances, the POST will display an error message; however, if the BIOS detects an error before it can access the video card, or if there is a problem with the video card, it will produce a series of beeps, and the pattern of the beeps indicates what kind of problem the BIOS has detected.
Because there are many brands of BIOS, there are no standard beep codes for every BIOS.

The two most-used brands are AMI (American Megatrends International) and Phoenix.

Below are listed the beep codes for AMI systems, and here are the beep codes for Phoenix systems.

AMI Beep Codes

Beep Code Meaning
1 beep DRAM refresh failure. There is a problem in the system memory or the motherboard.
2 beeps Memory parity error. The parity circuit is not working properly.
3 beeps Base 64K RAM failure. There is a problem with the first 64K of system memory.
4 beeps System timer not operational. There is problem with the timer(s) that control functions on the motherboard.
5 beeps Processor failure. The system CPU has failed.
6 beeps Gate A20/keyboard controller failure. The keyboard IC controller has failed, preventing gate A20 from switching the processor to protect mode.
7 beeps Virtual mode exception error.
8 beeps Video memory error. The BIOS cannot write to the frame buffer memory on the video card.
9 beeps ROM checksum error. The BIOS ROM chip on the motherboard is likely faulty.
10 beeps CMOS checksum error. Something on the motherboard is causing an error when trying to interact with the CMOS.
11 beeps Bad cache memory. An error in the level 2 cache memory.
1 long beep, 2 short Failure in the video system.
1 long beep, 3 short A failure has been detected in memory above 64K.
1 long beep, 8 short Display test failure.
Continuous beeping A problem with the memory or video.
[Read More…]

Nowadays as the Internet and other networks are greatly developed computer viruses are distributed rapidly and intensively. Everyday several new viruses capable to damage considerably your computer system arise. Anti-virus specialists work hardly to make updates their software against new viruses as soon as possible. The viruses can get inside computer in different ways. That is why there is no simple method to protect system. Only series of measures can give you reliable protection from the infection. Below are 9 steps to protect MS Windows based PC system from viruses.

1. Make regular backups.
It should be said that there is no absolutely safe way of protection. Virus creators regularly find holes in new computer products to use them for infection of computer systems. Some dangerous viruses can considerably damage data files or even erase entire file system. Make regular backups of your data files to separate file storage device. It can be separate hard drive, flash card, compact disc or another file storage device which you choose. To ease the procedure you can use some automatic backup software. And be ready if the system will die because of virus infection.

2. Be ready to reinstall your system if it dies because of viruses.
Get distributives of your operation system and distributives of software which you use and keep them together, for instance, on a set of CDs not far away from you. In this case if virus infection will cause unrecoverable system failure you can rapidly reinstall your working medium.

3. Protect your network connection with Firewall.
Firewall is a software which blocks suspicious potentially dangerous connections to preventing viruses from network to penetrate into your system. Windows XP system has quit simple but reliable built-in firewall. You can enable it as follows. 1) in Control Panel, double-click Networking and Internet Connections, and then click Network Connections. 2) Right-click the connection on which you would like to enable firewall, and then click Properties. 3) On the Advanced tab, check the option to Protect my computer and network.

If you need more flexible control of connections with network you can get and install more advanced firewall software like Norton Personal Firewall or Outpost Firewall. If you use this software you have ability to permit or to block particular connections and to monitor network activity.
[Read More…]